Skip to main content

Lace it up!


I love lace up shoes that tie around the ankle. I think they are incredibly adorable and using cute ribbon for the laces makes them even better. Recently I went shoe shopping for some cute flats that I could wear with capri pants this summer. I found a canvas pair I liked with cute tie up laces but they were $50! Seriously? For canvas? No way.

I put on my crafting hat (yes I have a crafting hat), drank some crafting elixir (I call it wine) and I started to hatch a plan. Why not get cheap canvas shoes that I see year after year in discount stores and jazz them up myself? So that is exactly what I did.


Supplies
9-ft ribbon that is .75" to 1.5" wide
12-.25" Eyelets
Eyelet tool
Hammer
Xacto Knife
Scissors
Marking Chalk
Straight Pins
Cheap canvas shoes (I got mine from Walmart under $10)
Hammer

  1. Cut the ribbon in half. Using the straight pins and ribbon, start to figure out the placement of the grommets. Where you pin the ribbon to the shoe will be where you place the grommets. Carefully try on the shoe with pinned ribbon to see if you like the placement of the ribbon. After you have the placement the way you like it, mark the areas with wash away chalk.
  2. Using the Xacto knife, carefully cut a hole for the grommet. Make sure not too cut the hole too large or the grommet will not hold. I basically start with a little cut and slowly make it larger, periodically placing the grommet in the hole to check the size.
  3. From the outside of the shoe, insert the deep half of the eyelet in the hole. Position the shallow half of the eyelet over stem of the front eyelet.
  4. Work on a firm, protected surface (I usually use a basement floor or a hard work table, something you don't care if it gets a mark or two). Position the front side (eyelet on the outside of the shoe) on the anvil and insert the tool into the eyelet center that is on the inside of the shoe. Hammer gently.
  5. Repeat steps 2 through 4 with the remaining grommet position.

  6. Lace the ribbon through the grommets making sure to start at the base by putting the ribbon under so it is inside the shoe and does not show on the outside of the shoe.

Hint: if your ribbon is polyester or acrylic use matches or a lighter to slightly singe the ends to stop fraying.

Comments

Popular posts from this blog

Leather Earring Tutorial

Why should leather only be used for jackets, shoes and purses? Medium weight or upholstery leather is easy to craft since it doesn't fray or crinkle. These leather earrings are quick, versatile and easy to make. You can even recycle those old purses or jackets that have damage since you really only need small amounts of good leather. I used 4" square leather samples and had plenty left over to make more earrings. Supplies: Leather Leather punch (I bought mine at Michaels Craft store for around $10 but you can also get the from home stores like Home Depot or Lowes) Sharp scissors 2-Large Jump Rings 2-Earring wires Jewelry pliers Download the pattern below, print and cut out shapes. Cut 2-of each shape in the leather of your choice. I used 3 different types of leather, don't be afraid to mix it up. Pile one set of the three shapes on top of each other and carefully punch a whole on one of the ends. I punched the hole about a quarter of an inch away from the end using the sma

Leather Earring Pattern Update

In October I posted a tutorial to make leather earrings . Well for Christmas I revisited this craft and made a few other designs for a few people at my work. This is one of my favorite tutorials because they are so easy to make and the earrings are light and easy to wear. I liked the new designs so much I thought I would share the pattern for them. To view the full set of instructions on how to make these leather earrings, click here . To make one of the two pairs shown, download and print the updated pattern below (the bottom row are the new designs):

Washer Necklace Tutorial

Every time I buy furniture that requires assembly I always left over hardware. I take this hardware and put it in a jar thinking that one day I will need that extra nut or bolt. Well today is that day! Below is a tutorial on how to take those extra washers and make them into a cute necklace. Supplies: Scissors X-acto knife or hole punch Pencil Small piece of scrapbooking paper (you can use the left over scraps for this project) Modge Podge (or something similar) Washer Aleene’s Paper Glaze 36” of ribbon or cord Use the washer to trace a circle on the paper, don’t forget to trace the inside circle as well. Using your scissors cut just inside of the traced line on the outer circle. Note: you want to cut inside of the line and not on it so it fits on the washer and does not overlap the edges. If the hole for your center is close to the same size of a hole punch, simply punch out the center circle. If not use the X-acto knife to cut out the center area. Modge Podge the paper to the washer